FT-2000 Firmwre更新履歴 [アマチュア無線（FT2K）]
FW Ver 1.21
1.DVR noise burst
2.DNF update
3.Noise Blanker update
4.60 Meter mode data corruption
5.SSB talk power
6.Speech Processor update
FW Ver 1.24
1.This fixes the ADJ. ERR problem.
FW Ver 1.27
1.Changes Tot timer default and a Equalizer default
FW Ver 1.29
1.Permit full break-in QSK operation up to 40 WPM.
2.Permit CAT command EX1205 acknowledgement to 20 khz.
3.The 139 tUad PE3 LVL default is changed from +6 to+3.
FW Ver 1.31
1.Permits monitoring the recording contents in DVS during the transmission of a message that was deleted after v o124
FW Ver 1.33
1.MENU116 add 5Hz step to tuning dial steps
2.The software version can be displayed on the radio
Old the three buttons GEN+50+ENT then turn the RADIO ON
the software versione wil be displayed for 2 seconds as XX.XX Y.YY
XX.XX as DSP version and Y.YY as FW: 10.24 1.33
EDSP Ver 10.29 (for > V.120 only)
1.Improve the FM audio (check exactly procedure)
FW Ver 1.34
1.MENU053/055 correct keyer bug
2.Permit monitoring DVS on the internal/external audio speacker during TX that was affected
by v0133 on some radios
3.not explained on the readme: changed the GEN-50-ENT routine with "BLACK LCD" during EDSP/FW release info
FW Ver 1.35
1.Upgrade for customer service nd factory allignement only!
Without change from 1.34 !?!
ndr.: RIDICOLOUS!!!!!!!
FW Ver 1.37
• Addition of CAT command "RI" (To turn "TX""RX" on and off in PCC）
• The QMB marker 014 diSP QMB MKR is corrected to center.
• Change MIC-SEL 073 F3E MIC SEL so the Front is not chosen for DATA/PC in-put.
• PITCH and SPEED will be displayed for two seconds when the control is adjusted. It is no longer necessary to hold the Keyer or Monitor button.
• Provide a more noticeable change for MENU SHAPE and PASSBAND.
SHAPE: 093 rdSP CW SHAP, 096 rdSP PKT SHP, 099 rdSP RTY SHP, 102 rdSP SSB SHP
PASSBAND: 094 rdSP CW SLP, 097 rdSP PKT SLP, 100 rdSP RTY SLP, 103 rdSP SSB SLP
• Output value of the MENU SHAPE DSP is reversed.
093 rdSP CW SHAP, 096 rdSP PKT SHP, 099 rdSP RTY SHP, 102 rdSP SSB SHP
• The Carrier Point frequency is optimized for CW reception.
• Correct WIDTH indication to show correctly during Antenna Tune operation.
• Correct the Tuning Offset Indicator during Power On at PITCH 300Hz CW mode.
FW Ver 1.38
- Corrected a “bug” of version 0137. In split frequency operation, which caused incorrect
mode change between the sub VFO-B and the main VFO-A on RX
- Reduce the response time of the main & sub S meter, for more suitable readings.
ここはとても役立つ。すごい情報量！！
http://web.ticino.com/wlog/ft2000/
1.DVR noise burst
2.DNF update
3.Noise Blanker update
4.60 Meter mode data corruption
5.SSB talk power
6.Speech Processor update
FW Ver 1.24
1.This fixes the ADJ. ERR problem.
FW Ver 1.27
1.Changes Tot timer default and a Equalizer default
FW Ver 1.29
1.Permit full break-in QSK operation up to 40 WPM.
2.Permit CAT command EX1205 acknowledgement to 20 khz.
3.The 139 tUad PE3 LVL default is changed from +6 to+3.
FW Ver 1.31
1.Permits monitoring the recording contents in DVS during the transmission of a message that was deleted after v o124
FW Ver 1.33
1.MENU116 add 5Hz step to tuning dial steps
2.The software version can be displayed on the radio
Old the three buttons GEN+50+ENT then turn the RADIO ON
the software versione wil be displayed for 2 seconds as XX.XX Y.YY
XX.XX as DSP version and Y.YY as FW: 10.24 1.33
EDSP Ver 10.29 (for > V.120 only)
1.Improve the FM audio (check exactly procedure)
FW Ver 1.34
1.MENU053/055 correct keyer bug
2.Permit monitoring DVS on the internal/external audio speacker during TX that was affected
by v0133 on some radios
3.not explained on the readme: changed the GEN-50-ENT routine with "BLACK LCD" during EDSP/FW release info
FW Ver 1.35
1.Upgrade for customer service nd factory allignement only!
Without change from 1.34 !?!
ndr.: RIDICOLOUS!!!!!!!
FW Ver 1.37
• Addition of CAT command "RI" (To turn "TX""RX" on and off in PCC）
• The QMB marker 014 diSP QMB MKR is corrected to center.
• Change MIC-SEL 073 F3E MIC SEL so the Front is not chosen for DATA/PC in-put.
• PITCH and SPEED will be displayed for two seconds when the control is adjusted. It is no longer necessary to hold the Keyer or Monitor button.
• Provide a more noticeable change for MENU SHAPE and PASSBAND.
SHAPE: 093 rdSP CW SHAP, 096 rdSP PKT SHP, 099 rdSP RTY SHP, 102 rdSP SSB SHP
PASSBAND: 094 rdSP CW SLP, 097 rdSP PKT SLP, 100 rdSP RTY SLP, 103 rdSP SSB SLP
• Output value of the MENU SHAPE DSP is reversed.
093 rdSP CW SHAP, 096 rdSP PKT SHP, 099 rdSP RTY SHP, 102 rdSP SSB SHP
• The Carrier Point frequency is optimized for CW reception.
• Correct WIDTH indication to show correctly during Antenna Tune operation.
• Correct the Tuning Offset Indicator during Power On at PITCH 300Hz CW mode.
FW Ver 1.38
- Corrected a “bug” of version 0137. In split frequency operation, which caused incorrect
mode change between the sub VFO-B and the main VFO-A on RX
- Reduce the response time of the main & sub S meter, for more suitable readings.
ここはとても役立つ。すごい情報量！！
http://web.ticino.com/wlog/ft2000/
いつも情報ありがとうございます。
ＧＷ中にＦＷ更新に挑戦してみます。
記事中紹介いただいたリンク先、確かにすごいですね。サービスマニュアルまで公開しているとは！これって日本では絶対やらないですね。
by Atsu (2008-04-27 20:59)